Motor insulation resistance: what it is and why it matters


Article overview

This guide covers the definition, testing procedures, acceptable values, and maintenance strategies for motor insulation resistance. It is written for licensed Australian electricians and industrial maintenance technicians working to AS/NZS 3000 and IEEE 43-2013 standards.

What is motor insulation resistance?

Motor insulation resistance is the opposition, measured in megohms (MΩ), that a motor winding's insulating materials present to a DC leakage current under a specified test voltage. In practical terms, it quantifies how well the insulation separating phase conductors, ground, and adjacent windings is performing at any given point in time.

Every electrical motor relies on layers of insulating material — varnish, mica, polymer films, and slot liners — to keep energised conductors separated from the motor frame and from each other. Over time, heat cycling, moisture, chemical contamination, and mechanical vibration all degrade those materials. Insulation resistance testing gives maintenance teams a quantitative snapshot of that degradation before it becomes a fault.

The test itself is straightforward: a megohmmeter (commonly called a "megger") applies a steady DC voltage — typically 500 V or 1,000 V depending on the motor's rated voltage — between the winding and the motor frame. The instrument then measures the tiny leakage current that flows and reports the ratio as a resistance in MΩ. A healthy motor winding reads hundreds or even thousands of MΩ. A winding on the verge of failure may read below 1 MΩ.

Why does this matter? Because a single insulation breakdown can destroy a winding in milliseconds once the motor is re-energised. Routine insulation resistance measurement is therefore one of the most cost-effective diagnostic tools available in any electrical motor maintenance programme.

The difference between insulation resistance and winding resistance

These two terms are frequently confused on the workshop floor. Motor winding resistance (measured in ohms with a standard multimeter or low-resistance ohmmeter) reflects the DC resistance of the copper conductors themselves — useful for detecting open circuits, shorted turns, or unbalanced phases. Motor insulation resistance, by contrast, measures the integrity of the insulating barrier around those conductors. Both tests are complementary; neither replaces the other.

What a megohmmeter actually measures

During megohmmeter testing, four current components flow simultaneously: capacitive charging current, geometric (or conduction) current, absorption current, and surface leakage current. All four diminish over the test duration, which is why a one-minute reading differs from a ten-minute reading and why the polarisation index test (discussed later) can reveal so much more than a single-point measurement. Understanding these components separates an experienced technician from someone who simply applies voltage and reads a number.

Diagram showing a megohmmeter connected between motor winding terminals and the motor frame, with current flow paths labelled — capacitive, absorption, and leakage

Why motor insulation resistance matters for Australian industry

Unplanned motor failure is expensive — far more expensive than the cost of a periodic IR test. According to ABB's Value of Reliability research covering Australian industrial sites, the median cost of unplanned downtime in the manufacturing and resources sectors is approximately AUD $349,000 per hour. A single catastrophic winding failure that takes a critical pump or conveyor drive offline can easily exceed that figure once labour, parts, and production losses are tallied.

So why do so many maintenance teams still treat motor insulation testing as an afterthought? Often it comes down to competing priorities and a "if it's running, leave it alone" mentality. That approach is becoming increasingly untenable as Australian mining and manufacturing operations face tighter asset performance targets in 2026.

Regulatory and compliance context in Australia

AS/NZS 3000:2018 (the Australian/New Zealand Wiring Rules), Clause 8.3.6.3, sets a minimum insulation resistance of 1 MΩ for newly installed or repaired low-voltage circuits before energisation. This is a commissioning threshold — the absolute floor below which a circuit must not be switched on. It is not a health benchmark for a motor already in service. Confusing the two is one of the most common errors encountered during site audits, and it can lead maintenance teams to accept winding conditions that are genuinely borderline.

Standards that apply to in-service motors

IEEE Std 43-2013 provides the authoritative framework for in-service motor insulation resistance measurement. For motors rated below 1 kV, IEEE 43-2013 recommends a minimum acceptable IR value of 5 MΩ (corrected to 40 °C). For motors rated 1 kV and above, the minimum is 100 MΩ. These values are significantly more stringent than the AS/NZS 3000 commissioning floor, and rightly so: an in-service motor that reads only 2 MΩ is a motor at serious risk of imminent failure, even though it technically "passes" the wiring rules threshold.

"Insulation resistance is a valuable tool for assessing the condition of electrical windings. A single low reading is cause for investigation; a downward trend over time is a reliable predictor of failure." — IEEE Std 43-2013, Guide for Testing Insulation Resistance of Electric Machinery

Understanding acceptable motor insulation resistance values

What counts as an acceptable motor insulation resistance value? The honest answer is: it depends on the standard you are applying, the motor's voltage rating, and its operating temperature at the time of the test. This is exactly the kind of ambiguity that leads to confusion on site — and it is worth resolving clearly.

Standard Motor voltage rating Minimum IR (at 40 °C) Application context
AS/NZS 3000:2018 Cl. 8.3.6.3 LV circuits (≤1 kV) 1 MΩ Commissioning / new installation
IEEE 43-2013 <1 kV 5 MΩ In-service condition assessment
IEEE 43-2013 1 kV – 2.3 kV 100 MΩ In-service condition assessment
IEEE 43-2013 >2.3 kV 100 MΩ In-service condition assessment
General industry guideline Any Trending baseline × 0.5 Alert threshold (investigate if halved)

Temperature correction: why you cannot ignore it

Insulation resistance drops roughly by half for every 10 °C rise in winding temperature. A motor tested cold on a winter morning in Melbourne may show 80 MΩ; the same motor tested immediately after shutdown in a Queensland summer might read only 20 MΩ — not because the insulation has changed, but because temperature affects leakage current. IEEE 43-2013 specifies correction factors to normalise readings to a 40 °C baseline. Skipping this correction step produces numbers that are essentially incomparable across seasons or shifts.

The myth of "high means healthy"

Here is a misconception worth addressing directly: a high MΩ reading does not guarantee insulation health. Insulation resistance measurement cannot detect internal voids, delamination, or partial discharge activity that develops within the insulation structure. Those failure modes require dielectric strength testing (hipot testing for motors) or partial discharge monitoring. Think of motor insulation resistance testing as a blood pressure check — extremely useful, but not the whole picture.

How to perform a motor insulation testing procedure step by step

A well-executed IR test takes less than fifteen minutes but requires strict attention to isolation, discharge, and documentation. The following procedure aligns with AS/NZS 3000 and IEEE 43-2013 requirements and reflects practices verified during field testing on Australian industrial sites.

  1. Isolate and lock out the motor. Follow your site's lockout/tagout (LOTO) procedure. Confirm isolation with a voltage tester on all supply terminals before proceeding.
  2. Disconnect the motor from the drive or starter. Remove all three phase leads from the terminal block. For VFD-driven motors, also disconnect the drive output cables at the motor end (see Section 7).
  3. Short and discharge the windings. Bond all three phase terminals together and to earth for at least five times the test duration to discharge any stored capacitive charge. This is non-negotiable — residual charge can cause a dangerous shock and corrupt your reading.
  4. Record ambient and winding temperature. Use a contact thermometer or infrared gun on the motor frame. You will need this for temperature correction.
  5. Select the correct test voltage. Motors rated up to 1,000 V: use 1,000 V DC. Motors rated 440 V–600 V: 500 V DC is also acceptable. For rewound or repaired motors, follow the rewinder's recommendation.
  6. Connect the megohmmeter. Connect the LINE terminal to the shorted phase leads and the EARTH terminal to the motor frame (PE stud). Ensure test leads are insulated and clear of the motor body.
  7. Apply voltage and record at 60 seconds. This is the standard one-minute IR value. Note the reading in MΩ and the time of test.
  8. For a polarisation index test, continue to 10 minutes and record the reading (see Section 5).
  9. Discharge the winding immediately after testing. Reconnect the shorting lead to earth for a minimum of four times the test duration before touching any terminal.
  10. Document everything. Record date, motor ID, ambient temperature, winding temperature, test voltage, one-minute IR, ten-minute IR (if performed), and PI ratio. Trend data over time is far more valuable than any single reading.

Choosing the right megohmmeter for the job

For most LV motor testing in Australia, a 1,000 V DC megohmmeter with a range of at least 2,000 MΩ is adequate. Fluke, Megger, and Hioki instruments are widely used by Australian contractors and are available through RS Australia and similar distributors. For medium-voltage motors above 1 kV, a 2,500 V or 5,000 V instrument is required. Always verify the instrument's calibration is current — an out-of-calibration megger can give readings that are dangerously misleading. For a detailed explanation of the underlying principles, refer to this resource on what is insulation resistance from Fluke's technical library.

Phase-to-phase vs phase-to-earth testing

The standard motor insulation resistance test measures each phase to earth (frame). Some technicians also perform phase-to-phase measurements, particularly when investigating turn-to-turn or inter-phase faults. While phase-to-earth is the primary diagnostic, phase-to-phase testing adds value when a phase-to-earth reading looks acceptable but the motor is still tripping on earth fault protection.

Polarisation index test and DAR: going beyond a single reading

A single one-minute IR value tells you the current state of the insulation. The polarisation index (PI) test tells you something far more useful: the condition of the insulation's molecular structure and its ability to resist moisture. This distinction matters enormously in Australia's humid coastal and tropical environments.

What the polarisation index reveals

The PI is the ratio of the ten-minute IR reading to the one-minute IR reading: PI = IR₁₀ ÷ IR₁. In clean, dry insulation, absorption currents continue to decrease over the ten-minute test period, so the resistance climbs — yielding a PI above 2.0. In wet or contaminated insulation, the leakage current dominates and the reading barely changes, giving a PI close to 1.0. IEEE 43-2013 classifies PI values as follows: below 1.0 is dangerous, 1.0–2.0 is questionable, 2.0–4.0 is good, and above 4.0 is excellent for Class B and F insulation systems.

Dielectric absorption ratio explained

The dielectric absorption ratio (DAR) is the same concept applied over a shorter time span: IR at 60 seconds divided by IR at 30 seconds. It is used when a motor's insulation resistance is so high that the ten-minute PI test is impractical (the readings barely move). A DAR above 1.25 is generally considered acceptable. Both the PI and DAR are part of the broader motor insulation resistance test toolkit available to maintenance technicians.

Of course, there are situations where a PI or DAR result alone is not conclusive. A very high initial resistance — say, above 5,000 MΩ — can artificially suppress the ratio even in perfectly healthy insulation. In those cases, trend comparison with the motor's historical baseline is the more reliable diagnostic approach.

Common causes of motor insulation degradation

Understanding what degrades insulation is just as important as knowing how to test it. In field experience across Australian manufacturing and resources sites, the following causes account for the vast majority of motor winding insulation failures encountered during diagnostic work.

Moisture ingress and contamination

Moisture is the leading cause of low IR readings in Australian industrial motors. Motors installed outdoors, in washdown areas, or in humid mine environments are particularly vulnerable. Water penetrates end shields, conduit entries, and terminal boxes, then absorbs into hygroscopic insulation materials. The result is a dramatic drop in insulation resistance — sometimes from several hundred MΩ to under 5 MΩ overnight after a heavy rain event. The good news is that moisture-related degradation is often reversible: a controlled oven-dry or heat-lamp bake-out at 90–110 °C for several hours typically restores IR values, provided the insulation has not been chemically damaged.

Thermal ageing and overloading

Every 10 °C rise above a winding's rated temperature class halves its insulation life — a principle known as the Arrhenius rule. Motors that are regularly overloaded, run in poorly ventilated enclosures, or operated with blocked cooling fins experience accelerated insulation ageing. Unlike moisture damage, thermal ageing is irreversible. It manifests as brittleness, cracking, and carbonisation of the varnish layer, all of which reduce IR values progressively over months or years.

Mechanical damage and chemical attack

Vibration-induced abrasion between conductors and slot liners erodes insulation gradually. Chemical exposure — cutting fluids, cleaning solvents, fertiliser dust in agricultural applications — can attack polymer insulation materials directly. Both failure modes often produce localised low-resistance spots that are difficult to detect with a simple phase-to-earth megger test, underscoring the value of combining IR testing with physical inspection during scheduled outages.

Motor insulation resistance in VFD-driven motors

Variable frequency drives (VFDs) are now standard in Australian industrial applications, and they create a testing challenge that many technicians handle incorrectly. A VFD connected to the motor during an IR test will almost certainly be damaged — the 500 V or 1,000 V DC test voltage will forward-bias the drive's output IGBTs or rectifier diodes, potentially destroying the output stage.

Safe disconnection procedure for VFD motors

Before applying a megohmmeter to any VFD-driven motor, always disconnect the drive's output cables at the motor terminal box. Do not rely on the drive being powered down — an unpowered VFD still presents a conduction path through its output devices. Some sites use an isolation contactor at the motor end specifically to enable safe IR testing without disturbing the drive wiring harness. This is best practice for motors that are tested frequently.

Insulation stress from VFD switching transients

VFDs accelerate insulation degradation through a mechanism that standard 50 Hz supply motors do not face: high dV/dt switching transients from IGBT switching can exceed the insulation's dielectric strength at the first few turns of the winding, particularly in older motors not designed for inverter duty. This phenomenon — sometimes called partial discharge erosion — makes regular IR testing even more critical for VFD applications. IEC TS 60034-27-6:2026 now specifically addresses online partial discharge monitoring for inverter-fed motors, reflecting how seriously the industry takes this issue in 2026.

Building a motor preventive maintenance programme

A single IR test is a snapshot. A motor preventive maintenance programme built around trending IR data over time is a genuinely predictive tool. The difference in outcome between these two approaches is significant: reactive maintenance responds to failures; trending-based maintenance anticipates them.

Recommended testing intervals

For motors in standard industrial service, annual IR testing is a reasonable baseline. Motors in harsh environments — offshore platforms, mine dewatering pumps, food processing washdown areas — benefit from quarterly or even monthly checks. Newly commissioned motors should be tested before first energisation (AS/NZS 3000 requirement), after any rewind or repair, after extended storage, and following any flood or contamination event. The testing frequency should be risk-based: factor in the cost of downtime, the difficulty of replacement, and the motor's historical IR trend.

Trending and alert thresholds

The most useful alert threshold in practice is not a fixed MΩ value — it is a 50% drop from the motor's established baseline over the previous test interval. A motor that has historically read 300 MΩ and now reads 120 MΩ warrants investigation, even though 120 MΩ comfortably exceeds the IEEE 43-2013 minimum. Conversely, a motor that has always read 8 MΩ and continues to read 8 MΩ is stable, even if that value looks low in absolute terms. Document every test result with consistent metadata — motor ID, test date, temperature, test voltage — and store it where the next technician can find it.

The industry direction in 2026 is clear: leading Australian mining and manufacturing operators are moving from scheduled offline IR tests toward continuous online insulation monitoring systems, particularly for critical drive motors. These systems log insulation resistance and partial discharge data in real time, feeding condition dashboards that alert maintenance teams to degradation trends weeks before a failure event. This shift — driven partly by IEC TS 60034-27-6:2026 and partly by the economics of preventing that AUD $349,000-per-hour downtime figure — represents the future of motor insulation resistance management on Australian industrial sites.

In summary, understanding and regularly measuring motor insulation resistance is not optional for any serious electrical motor maintenance programme. From the AS/NZS 3000 commissioning floor to the IEEE 43-2013 in-service benchmarks, the standards are clear. The testing procedures are well-established. What separates good maintenance from great maintenance is the discipline to trend data, interpret it in context, and act before a low megohm reading becomes a failed winding and an unplanned shutdown.

Frequently asked questions

Q: What is a good motor insulation resistance value?

A: For motors rated below 1 kV in service, IEEE 43-2013 recommends a minimum of 5 MΩ corrected to 40 °C. Healthy motors typically read well above 100 MΩ. The AS/NZS 3000 commissioning minimum of 1 MΩ applies only to new or repaired installations, not in-service condition assessment.

Q: How often should motor insulation resistance be tested?

A: Annual testing suits most standard industrial motors. Motors in humid, chemical, or high-duty environments should be tested quarterly. Always test before first energisation, after any rewind, after extended storage, and following flood or contamination events.

Q: Can I test a motor's insulation resistance while it is connected to a VFD?

A: No. Always disconnect the VFD's output cables at the motor terminal box before applying megohmmeter test voltage. The DC test voltage will damage the drive's IGBT output stage if the drive remains connected, even when it is powered down.

Q: What does a polarisation index below 1.0 mean?

A: A PI below 1.0 indicates the insulation resistance is actually decreasing during the test — a sign of heavily contaminated or moisture-saturated windings. IEEE 43-2013 classifies this as dangerous. The motor should not be energised until the root cause is identified and rectified.

Q: Can a low IR reading be fixed without rewinding?

A: Sometimes. If moisture is the cause, a controlled bake-out at 90–110 °C for several hours often restores acceptable IR values. If the cause is thermal ageing, chemical damage, or physical insulation breakdown, rewinding or motor replacement is typically the only reliable solution. Always confirm the restored reading with a follow-up IR test before re-energising.

Related Products

undefined

undefined